#
# VOIP BLASTER CONFIGURATION FILE (vb.txt is example, vb.ini is used)
#
# 1> quotes not really required unless you want with space in the entry
# 2> if don't specify the ':port' in address entries, then the default port
#    will be assumed
# 3> usually only need to set the PUBLIC_ADDRESS if have multiple machines
#    running this software behind a single public address and using
#    port-remapping to get to each of them, even then can use an address of
#    0.0.0.0:port, where 'port' is replaced with the desired port number.
#

# select which device to use, default is 0 if commented out
#DEVICE_INDEX     1

# can enable lots of debug stuff here, default is 0 if commented out
#DEBUG_LEVEL      9

# this sets the volume level inside the device
# 0 = lowest, 6 = highest, 3 = default
 DEVICE_VOLUME    3

# how long (in tenths of a second) to make CPC signal, many answering
# machines expect this to notice the caller hungup, a good value is
# around 5, disabled if commented out.
#CPC_DURATION     5

# set to zero if do not want to use '#' to start call at end of dialed digits
# enabled if commented out or value set to 1.
#FORCE_DIAL       0

# these have to do with how much latency/jitter to allow
# bumping up NET_HIGH_COUNT can help alot if have lots of jitter
# ususally caused by TCP retrans, but will increase delay as well, but
# will give better quality speech.
 NET_HIGH_WATER   2
 NET_HIGH_COUNT   4
#NET_HIGH_COUNT  16
#NET_HIGH_COUNT  32

# use this port for outgoing calls unless explicitly given
 PORT_OUTGOING    8008

# use this port for incoming calls (port 'vb' actually listens to)
 PORT_LISTEN      8008

# remove this to disable voice over UDP
 PORT_LISTEN_UDP  8010

# use this port for phonebook server unless explicitly given
 PORT_SERVER      8009

# set to YES if want to use HTTP protocol for phonebook server access
# must set PORT_SERVER to 80 also
 HTTP_SERVER      NO

# address for phonebook server (only primary used for now)
 PHONEBOOK_SERVER "vs1.fobbit.net"
 PHONEBOOK_SERVER "vs2.fobbit.net"

# Information to publish to phonebook server
# Should only set PUBLIC_ADDRESS if inbound is via a NAT box, even then,
# unless want port-redirection should not need to set, since server will
# use the 'recv-from' address as the default. Can use something like
# "0.0.0.0:8158" if only what to set the port for NAT redirection.
# Generally the port in the PUBLIC_ADDRESS should match PORT_LISTEN unless
# you know what you are doing (same for UDP versions)
# The NAME, LOCATION, and EMAIL are not required in anyway to use the
# phonebook server but would appreciate it if at least said what
# part of the world you are in (i.e. country or continent).
# if you give your email will only use it to try and help if I notice
# a problem, and perhaps email you about program updates.
#PUBLIC_ADDRESS     "0.0.0.0:8008"
#PUBLIC_ADDRESS_UDP "0.0.0.0:8010"
 PUBLIC_NAME        "Someone"
 PUBLIC_LOCATION    "Somewhere"
 PUBLIC_EMAIL       "foo@bar.com"

# if set both of these to NO will act like before (without phonebook server)
 PUBLISH_TO_SERVER  YES
 QUERY_SERVER       YES

# this should only be set to NO if can't accept inbound tcp connections
# because blocked by a firewall/nat box, if at all possible should leave
# yes and add redirect rules to firewall/nat box. This currently doesn't
# really do anything, but if you can't accept tcp connections on the inbound
# port, won't be able to receive calls
 CAN_ACCEPT_INBOUND YES

# various sound files to use, seems if use dialtone file causes dialing issues
# ringback and busy are required, but if dialtone not specified uses builtin
 FILE_RINGBACK         "sounds/ringback.723"
 FILE_BUSY             "sounds/busy.723"
#FILE_DIALTONE         "sounds/dialtone.723"
 FILE_DIALTONE_HEADSET "sounds/dialtone.723"

# this controls how to dial, first is number of seconds from off-hook till
# must enter the first digit, second is how many seconds from last digit
# until the program initiates the call
 DIAL_TIMEOUT_1     15
 DIAL_TIMEOUT_2     5

# when dial, first check local DIALED table, use ip/port direct if a match
# else check speed table, convert to serial-number if so and use, else
# use directly as a serial-number. send serial-number to phonebook server
# for lookup

# the dialed digits table is used to map dialed digits to an IP address:port
# this is mainly used if don't want to use the phonebook-server
# the 2nd column is what the user dials and the 3rd column is the destination
# ip:port to use for the call, if no port is specified then the default
# outgoing port is used (PORT_OUTGOING), any number of dialed digits can
# be used and can vary from one entry to another
#DIALED 100         hostname1:8008
#DIALED 101         hostname2:8008
#DIALED 102         hostname3:8119
#DIALED 202         hostname5
#DIALED 411         hostname6

# map dialed digits to a serial-number (only usefull with phonebook-server)
# entry number '1' is for a windows box that is hooked up to an answering
# machine that anyone is free to use for testing, again any number of dialed
# digits can be used and can vary from one entry to another
 SPEED  1           104747227
#SPEED  2           10850????
#SPEED  3           10935????

#
# The End!
#